strong SRT 4620 reciever - Free to Air Satellite Forums (Asia Pacific) - Sponsored by aDigitaLife.com Audio Visual Suppliers

davecreek · 25-11-2003, 11:21 AM

How do Guy's?!

I have one of these. Does anyone else?

I am not sure if it is me or there is a problem with my setup.

I have several issues with it, for instance the other night I was watching TV and decided to turn it off and then back on again using the red button on the remote. I wanted to see what the time was. I noticed that I had lost various channels and with another restart I lost more. I had B1 and C1 and it was the C1's that disappeared.

Next morning I discovered that the TP's were missing. It was almost like the reciever was doing its own factory default?

Also I have noticed that the system clock was well the next morning when I looked at it. Could this be connected to the Moteck H-H that I have just installed? Could it be consuming too much power?

When I am editing the 'channel List", I notice that sometimes the thing will freeze up neccetating (spelling) a re boot.

I sat for 9 hours when I first got it waiting for the satellite to come back on. Then I did a re start and everything was working properly. My freind has one as well and they have had the the no reception thing but we put it down to the Wet west Coast weather and the fact we are using 76cm dishes rather than something bigger.

THe manufacturers wonder what my dish is etc but I can not see that the dish would affect the actual working of the set.

I am aware that these things are basically computers that are dedicated to one use but knowing computers.........

Anyone have similar stories with this type of symptoms?

Any ideas?

Cheers Dave Creek

**VK4BKP** · 25-11-2003, 11:47 AM

Over to decoders.

You could remove the Moteck and see if the problems persist, otherwise I think it might be broke (highly technical explanation).

I can't see how the dish would have anything to do with it either.

bassett · 26-11-2003, 01:24 AM

The only connection between the dish and the receiver is the 14 // 18 volt line, which switches to control the Moteck, then when the dish is repossitioned, the line switches back to the LNB,,
As vetrun said, disconnect the moteck,,, But it sounds like a power supply problem, involveing the 14 // 18 volt supply.

davecreek · 16-12-2003, 12:56 PM

THanks Guy's. Thats about what I figured too.

I have been in touch with the tech's and they said to return it and thats what I will do soon.

I brought a Topfield 3200, plugged it in and apart from a few teething issues with me learning to drive it it works.

Apart from one thing. When I tell the STB - via the remote control - to go from B1 to B3 it does. THen when I want to go back it won't.

I end up having to manually move it by going into the INSTALLATION MODE.

Any ideas why the dish will not work?

The Strong STB works the dish motor okay but the topfield doesn't. Both are Diseq 1.2 compliant and the top field is also USALS as well although I don't use that method of calibration.

Another strange thing is ABC TV. I used to have it on B1 12,258, 12,260 and 12,261. I lost it when ABC did their fibre optic link and so did my freind. Now I still can not get it but they have had it come back not many days later. They still watch it and I am unable to get it on the new Topfield either????

How long can the coax cable feed be? I am wondering if low voltage is the issue?

Does anyone understand how the H-H motor works in with the STB?

Cheers Dave Creek

rusty · 04-01-2006, 08:00 AM

im having the same problem on my reciever. It freezes especially when you edit the channel list. Some times when you switch it on it has no signal untill you reboot it.

davecreek · 04-01-2006, 09:23 PM

Quote:

Originally Posted by rusty

im having the same problem on my reciever. It freezes especially when you edit the channel list. Some times when you switch it on it has no signal untill you reboot it.

Hee Hee!

I shouldn't laugh really.

I sent the first one back and it was replaced under warranty with another - I never did find out what was wrong with the first one, of course why would they tell me?!

THe second one was later software version than the first.

This one does okay but from time to time it throws a wobbly for some unknown reason. I have to disconnect from the mains supply and re boot it. I can't wait for the day I can afford another one and really 'boot' this'n.

I also find it won't move the dish at times and I have re point it and re save the position and away it goes. That's stress I could do without.

I won't be ever buying another strong mostly due to the lack of support I got to my enquires. I suspect it is a software issue myself but I cannot rule out a voltage spike or something as I live next door to a small power station and here on the west coast we do get lightening which could cause a problem and I would not know it.

This is all probably of not much help though to you Rusty but what more can one say

.

Cheers Dave Creek
Hokitika NZ

jpsoni · 04-01-2006, 09:39 PM

I had a Strong 4620, after a few months of Headache even with the help of Wozza n Basset ,I got it fixed and quickly sold it a family friend who works 10 hours a day and like to watch a few channels.when she has time from her newly born son.
But it is still working, when I went to pay a visit n inserted new freqs.
We have a so called agent in Brisbane.

tytower · 05-01-2006, 03:51 AM

Gee your a nice fellow jpsoni.
They used to tell you at MLC AMP and all the other Life Assurance Coys ¨Go sell to all your relatives they are the easiest sales¨ And they did it too in most cases im told !

rusty · 04-07-2006, 08:51 AM

ok anyone know how to select Ku lnb under the lnb settings once you have deleted it. I cannot find a selection for this. Universal is no good to me as i wish to incoperate a 22kh switch into the system? anyone know how to select ku lnb????

davecreek · 05-07-2006, 12:50 AM

Quote:

Originally Posted by rusty

ok anyone know how to select Ku lnb under the lnb settings once you have deleted it. I cannot find a selection for this. Universal is no good to me as i wish to incoperate a 22kh switch into the system? anyone know how to select ku lnb????

What does the wide band option do? It will give you access to the 22kHz switch but will it pick up the Ku?

Another reason for not buying Strong.

Cheers Dave Creek
Hokitika

bassett · 05-07-2006, 03:11 AM

Quote:

Originally Posted by jpsoni

I had a Strong 4620, ,I got it fixed and quickly sold it a family friend .

just goes to show,, if you can't rip of your friends and family, who can you rip off

knucklehead · 05-07-2006, 06:31 AM

...sorry

jpsoni · 09-07-2006, 11:10 PM

But my family/ friends who only looks at AsiaSat 3, is happy with the trade n I am a phone away if he needs my guidance.
so far after a year it is still going. n I will be here for him,after the 12 months warranty period, where the original l seller would have gone.after 12 months.
But ,he only he paid half the original cost.

rusty · 10-07-2006, 01:55 AM

Yep i paid only $80 NZD for mine and its fine. Only plays up if you do lots of channel editing. If you just watch tv its fine.

25-11-2003, 11:21 AM	#1
davecreek Junior Member Join Date: Sep 2003 Location: Hokitika New Zealand Posts: 17	strong SRT 4620 reciever How do Guy's?! I have one of these. Does anyone else? I am not sure if it is me or there is a problem with my setup. I have several issues with it, for instance the other night I was watching TV and decided to turn it off and then back on again using the red button on the remote. I wanted to see what the time was. I noticed that I had lost various channels and with another restart I lost more. I had B1 and C1 and it was the C1's that disappeared. Next morning I discovered that the TP's were missing. It was almost like the reciever was doing its own factory default? Also I have noticed that the system clock was well the next morning when I looked at it. Could this be connected to the Moteck H-H that I have just installed? Could it be consuming too much power? When I am editing the 'channel List", I notice that sometimes the thing will freeze up neccetating (spelling) a re boot. I sat for 9 hours when I first got it waiting for the satellite to come back on. Then I did a re start and everything was working properly. My freind has one as well and they have had the the no reception thing but we put it down to the Wet west Coast weather and the fact we are using 76cm dishes rather than something bigger. THe manufacturers wonder what my dish is etc but I can not see that the dish would affect the actual working of the set. I am aware that these things are basically computers that are dedicated to one use but knowing computers......... Anyone have similar stories with this type of symptoms? Any ideas? Cheers Dave Creek

16-12-2003, 12:56 PM	#4
davecreek Junior Member Join Date: Sep 2003 Location: Hokitika New Zealand Posts: 17	THanks Guy's. Thats about what I figured too. I have been in touch with the tech's and they said to return it and thats what I will do soon. I brought a Topfield 3200, plugged it in and apart from a few teething issues with me learning to drive it it works. Apart from one thing. When I tell the STB - via the remote control - to go from B1 to B3 it does. THen when I want to go back it won't. I end up having to manually move it by going into the INSTALLATION MODE. Any ideas why the dish will not work? The Strong STB works the dish motor okay but the topfield doesn't. Both are Diseq 1.2 compliant and the top field is also USALS as well although I don't use that method of calibration. Another strange thing is ABC TV. I used to have it on B1 12,258, 12,260 and 12,261. I lost it when ABC did their fibre optic link and so did my freind. Now I still can not get it but they have had it come back not many days later. They still watch it and I am unable to get it on the new Topfield either???? How long can the coax cable feed be? I am wondering if low voltage is the issue? Does anyone understand how the H-H motor works in with the STB? Cheers Dave Creek Last edited by davecreek; 16-12-2003 at 12:59 PM.

04-01-2006, 09:39 PM	#7
jpsoni Satellite Guru Join Date: May 2004 Location: Queensland,Australia Posts: 1,539	I had a Strong 4620, after a few months of Headache even with the help of Wozza n Basset ,I got it fixed and quickly sold it a family friend who works 10 hours a day and like to watch a few channels.when she has time from her newly born son. But it is still working, when I went to pay a visit n inserted new freqs. We have a so called agent in Brisbane. Last edited by jpsoni; 04-01-2006 at 09:40 PM. Reason: spelling

05-01-2006, 03:51 AM	#8
tytower Member Join Date: Dec 2005 Location: NorthernNSW Posts: 462	Gee your a nice fellow jpsoni. They used to tell you at MLC AMP and all the other Life Assurance Coys ¨Go sell to all your relatives they are the easiest sales¨ And they did it too in most cases im told ! __________________ Property and Family are not Government issues Governments should do what they were designed to do-Handle the national issues not the private.

04-07-2006, 08:51 AM	#9
rusty Senior Member Join Date: Jun 2005 Location: New Zealand Posts: 558	ok anyone know how to select Ku lnb under the lnb settings once you have deleted it. I cannot find a selection for this. Universal is no good to me as i wish to incoperate a 22kh switch into the system? anyone know how to select ku lnb???? __________________ Optus B1,B3 and C1, Panamsat 8 and AMC 23 on a fixed 90cm ihug with 5 lnbs. Panamsat 8 C band 3 meter mesh.

25-11-2003, 11:47 AM	#2
VK4BKP Moderator Join Date: May 2003 Location: Mackay Posts: 5,710	Over to decoders. You could remove the Moteck and see if the problems persist, otherwise I think it might be broke (highly technical explanation). I can't see how the dish would have anything to do with it either.

26-11-2003, 01:24 AM	#3
bassett Satellite Guru Join Date: Apr 2003 Location: bassettville Where else Posts: 5,354	The only connection between the dish and the receiver is the 14 // 18 volt line, which switches to control the Moteck, then when the dish is repossitioned, the line switches back to the LNB,, As vetrun said, disconnect the moteck,,, But it sounds like a power supply problem, involveing the 14 // 18 volt supply.

04-01-2006, 08:00 AM	#5
rusty Senior Member Join Date: Jun 2005 Location: New Zealand Posts: 558	im having the same problem on my reciever. It freezes especially when you edit the channel list. Some times when you switch it on it has no signal untill you reboot it.

05-07-2006, 06:31 AM	#12
knucklehead Master Baiter Join Date: Jun 2003 Location: Canberra, the crapital Posts: 2,372	...sorry __________________ I'm no gynecologist, but I'll have a look! NO HOWARD

09-07-2006, 11:10 PM	#13
jpsoni Satellite Guru Join Date: May 2004 Location: Queensland,Australia Posts: 1,539	But my family/ friends who only looks at AsiaSat 3, is happy with the trade n I am a phone away if he needs my guidance. so far after a year it is still going. n I will be here for him,after the 12 months warranty period, where the original l seller would have gone.after 12 months. But ,he only he paid half the original cost. __________________ Thanks for reading this mail Wishing all members n their families the best of health. Last edited by jpsoni; 09-07-2006 at 11:14 PM.

10-07-2006, 01:55 AM	#14
rusty Senior Member Join Date: Jun 2005 Location: New Zealand Posts: 558	strong Srt 4620 Yep i paid only $80 NZD for mine and its fine. Only plays up if you do lots of channel editing. If you just watch tv its fine. __________________ Optus B1,B3 and C1, Panamsat 8 and AMC 23 on a fixed 90cm ihug with 5 lnbs. Panamsat 8 C band 3 meter mesh.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode